Cisco 300-110 Dumps

Question # 1

An engineer is conducting a Layer 2 site survey. Which type of client must the engineer match to the survey? 

A. best client available 
B. phone client 
C. normal client 
D. worst client available 

Show Answer

Question # 2

An enterprise network is deploying two Cisco Catalyst 9800 WLCs in a data center to ensure uninterrupted wireless services for a campus with thousands of users. The IT management requests a design that enables seamless failover without client reauthentication or loss of connectivity if one controller fails. Ease of configuration and ongoing management are high priorities. The controllers will be connected via a high-speed LAN segment, and both must support full active-passive redundancy for all managed APs. Which design approach meets the requirements? 

A. Configure the 9800 WLCs in separate mobility groups and synchronize configurations manually. 
B. Implement SSO with redundancy management interface and AP SSO enabled between the two controllers. 
C. Deploy the controllers with VRRP to provide gateway redundancy and manually synchronize WLAN profiles. 
D. Enable N+1 redundancy, assigning primary and secondary controllers to each AP, and use DHCP for failover. 

Show Answer

Question # 3

A company is upgrading its wireless infrastructure and is in a state of transition. Some parts of the company's building still run on the legacy WLC. The new WLC is not located at the same site as the legacy WLC. The company requires seamless client inter-controller roaming between the new WLC and the legacy WLC, with no disruptions. Both WLCs are separated by firewalls. Which troubleshooting command validates that the mobility control packets between the WLCs can be sent and received? 

A. mapping mobility_peer IP address 
B. debug mobility handoff enable 
C. debug mobility config enable 
D. mapping mobility_peer_management IP address 

Show Answer

Question # 4

A customer has a single anchor WLC named Anchor A. Anchor A is in a DMZ and provides guest access. The customer wants to deploy an additional anchor controller named Anchor B to provide redundancy if Anchor A fails. Which design approach should be taken for the guest WLAN priority on the foreign WLC for each anchor WLC?

 A. Set Anchor A to priority 3 and Anchor B to priority 3. 
B. Set Anchor A to priority 3 and Anchor B to priority 1. 
C. Set Anchor A to priority 1 and Anchor B to priority 1. 
D. Set Anchor A to priority 1 and Anchor B to priority 3. 

Show Answer

Question # 5

An engineer configured the optimized client roaming on Cisco WLC with an RSSI threshold of -72 dBm. Clients report frequent disconnections. What must be configured for the AP to guide the client to a better AP? 

A. Enable BSS transition on the SSID and optimized roaming at the radio level. 
B. Disable coverage hole detection on the SSID and enable BSS transition on the SSID. 
C. Enable BSS transition at the radio level and optimized roaming on the SSID. 
D. Disable optimized roaming and enable 802.11v support on the SSID. 

Show Answer

Question # 6

A customer has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity. 5 access points are set to high failover priority and 7 access points are set to critical failover priority. During a failure, not all critical access points failed over to the backup Cisco WLC. Which configuration is the cause of this issue? 

A. The high priority access point is oversubscribed. 
B. network ap-priority is set to enable. 
C. The critical priority access point count is oversubscribed. 
D. network ap-priority is set to disable. 

Show Answer

Question # 7

A wireless engineer is preparing for a meeting with a customer to discuss a new wireless network design. The customer is a company that develops code and occupies a three-story building. Which two information points does a pre-site survey questionnaire contain? (Choose two.)

A. total number of access points in use 
B. client devices that will connect to the wireless network 
C. access point density required 
D. model of the wireless controller 
E. applications that will run over the wireless network 

Show Answer

Question # 8

A customer has two Cisco Catalyst 9800 Series WLCs named WLC-A and WLC-B in an N+1 configuration with the same WLANs but different Layer 3 interfaces for each WLC, and APs in local mode. WLC-A manages Building A APs and WLC-B manages Building B APs. The customer wants users to remain connected and retain their session state including the IP address when moving between buildings. How must this requirement be incorporated into the design? 

A. Create a mobility tunnel between WLC-A and WLC-B with the same group name. 
B. Configure WLC-A and WLC-B in a high-availability cluster and set a mobility MAC address. 
C. Implement AP groups for each building by using the same name on WLC-A and WLC-B. 
D. Connect WLC-A and WLC-B by using the redundancy port to sync client sessions. 

Show Answer

Question # 9

An engineer must design AP placements for a new branch office that contains two floors. The engineer uses Ekahau to complete the predictive survey. To calculate the signal bleed through between floors, the engineer creates a building, adds the floors, and attenuation areas. After the scale is set, what else must be added on the floors to accurately measure the signal bleed at a specific location? 

A. Draw in coverage areas. 
B. Start the auto planner. 
C. Add alignment points. 
D. Choose the access point models.

Show Answer

Question # 10

Which strategies must the engineer use for the antenna deployment model in a warehouse? 

A. ceiling-mounted, directional antennas 
B. wall-mounted, low-gain, omnidirectional antennas 
C. ceiling-mounted, high-gain, omnidirectional antennas 
D. wall-mounted, patch directional antennas 

Show Answer

Question # 11

A small customer has a legacy autonomous mode Wi-Fi deployment that provides a lowdensity and low-capacity service. The customer wants to update and replace this  deployment with the latest Wi-Fi technology but has a fixed budget that will pay only to replace the APs. Which architectural controller deployment model suits this requirement?

A. embedded 
B. unified 
C. fabric 
D. cloud 

Show Answer

Question # 12

An enterprise network administrator is asked to set up an experimental WLAN for a collaboration project with a local service provider. The WLAN must be anchored to a WLC in the service provider data center using legacy mobility mode. After the configurations are completed on the WLCs and the firewalls in the path, the data path mobility tunnel is failing to come up. What should be performed by the administrator to debug the issue? 

A. Establish a Telnet connection from a local PC to the firewall on port 97. 
B. Use the mapping command on the WLC. 
C. Establish a Telnet connection from a local PC to the firewall on port 16666. 
D. Use the mping command on the WLC. 

Show Answer

Question # 13

Which profile is included within a site tag when configured in a Cisco 9800 WLC architecture? 

A. QoS 
B. NAT 
C. Flex 
D. VLAN 

Show Answer

Question # 14

How are mobility groups created, excluding mobility anchors? 

A. The WLCs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions. 
B. A mobility group does not require all WLCs in the group to use the same virtual IP address. 
C. Each WLC must use the same mobility domain name and be defined as a peer in each other's static mobility members list. 
D. If WLCs with HA SSO are deployed, each WLC in the WLC HA pair is considered separately as a mobility peer. 

Show Answer

Question # 15

A customer designs a Cisco wireless environment to provide connectivity to employees and guests. The guest SSID must be configured on three anchor WLCs named Anchor1, Anchor2, and Anchor3 in a DMZ. The guest anchor priority must be configured to ensure that Anchor1 has the highest priority. Which priority level must be incorporated in the design for Anchor1? 

A. 0 
B. 1 
C. 2 
D. 3 

Show Answer

Question # 16

A customer has a Cisco wireless network with two Cisco Catalyst 9800 Series WLCs in a high availability cluster, 50 Cisco 2800I APs, and all SSIDs and services are 5 GHz only. A security mandate requires that rogue APs be scanned and identified in 2.4 GHz and 5 GHz bands without impacting existing client connectivity. How must the wireless network be reconfigured to meet the requirement without purchasing additional APs? 

A. Set the XOR radio role to Client Serving and the slot 1 radio to Sniffer mode on all the APs. 
B. Set the XOR radio role to Monitor mode and the slot 1 radio to Client Serving on all the APs. 
C. Set the XOR radio role to Client Serving and the slot 1 radio to Monitor mode on all the APs. 
D. Set the XOR radio role to Sniffer mode and the slot 1 radio to Client Serving on all the APs. 

Show Answer

Question # 17

A university wants to deploy a high density of APs in an area where a high number of users congregate. Which functionality allows the university to optimize the RF settings for APs that operate in different environments or coverage zones? 

A. AP groups 
B. RF groups 
C. AP profiles 
D. RF profiles 

Show Answer

Question # 18

A wireless engineer is getting ready to perform a predictive site survey. The new network needs to support data and voice over wireless. Which two Cisco recommendations should be considered for the design? (Choose two.) 

A. Set -19 dBm of separation between APs on the same channel. 
B. Use the 5 GHz radio band due to 40 MHz bandwidth capability. 
C. Use the 5 GHz radio band due to the 24 non-overlapping channels. 
D. Set the cell boundary to -67 dBm. E. Set the cell overlap to 15% 

Show Answer

Question # 19

A consultant must design a WLAN for a large campus with high AP density, 50-100 clients per cell, 5 Mbps throughput per client minimum, 5 GHz and 2.4 GHz coverage at -67 dBm, and no 802.11b clients. Which two WLAN design approaches meet the requirements? (Choose two.) 

A. Set the minimum mandatory data rates to 12-18 Mbps. 
B. Configure up to six SSIDs on any AP. 
C. Enable 802.11b data rates. 
D. Reduce the 2.4 GHz coverage with FRA. 
E. Set the 5 GHz channel widths to 80-160 MHz. 

Show Answer

Question # 20

An engineer must perform a predictive design for a wireless network. The customer has devices that can tolerate at most 100 ms of delay when roaming. Which design criteria must be used? 

A. location 
B. data 
C. video 
D. voice 

Show Answer